CAPSUN Winding technology of aluminum electrolytic capacitor
Writer：Capacitor manufactur Source：未知 Time：2021-09-08 07:10:00
【DESCRIPTION】：Aluminum electrolytic capacitor element winding is also called wrapping and element winding.
It is to wrap the cathode aluminum foil and anode aluminum foil with electrolytic paper, and then use paste (made of polyvinyl alcohol) or adhesive tape to make aluminum electrolytic capacitor
1. Winding process and technical requirements:
1.1, anode foil and cathode foil overlap is good, if the anode foil and cathode foil overlap is not good, will cause the following phenomenon
a, The "effective" area (overlapping part) of the metal plate of the capacitor decreases, resulting in the decrease of the capacitance.
B, after winding, the element core pulling, as shown in the following figure
c, The prime is spiral, as shown below
1.2. The center point of the well wound prime and the two leads shall be in line without eccentricity, as shown in the figure
Bad winding condition, 4 legend
1.3. The distance between the two leads of the prime element and the distance between the holes of the sealing rubber plug shall be matched, otherwise, poor sealing will be caused, and leakage will be caused in serious cases, as well as the scratch (open circuit, semi open circuit) on the contact between the aluminum tongue and the aluminum foil, which will greatly shorten the service life of the capacitor.
The winding mandrel shall be selected according to the outer diameter of the product, as shown in the table below. For the data in the table, the winding pins of different mandrel shall be selected. After winding, the element can be put into the aluminum shell smoothly, and a certain gap shall be reserved with the aluminum shell
Shell diameter / mm, ultra small, 5, 6, 8, 10, 13, 16, 18, 22
Mandrel diameter / mm 0.8 ~ 1.01.2 ~ 1.51.5 ~ 1.8 1.82.0 ~ 2.53 3.5 ~ 4 3.5 ~ 4 3.5 ~ 4
Aluminum electrolytic capacitor element winding is also called wrapping and element winding.
It is to wrap the cathode aluminum foil and anode aluminum foil with electrolytic paper, and then use paste (made of polyvinyl alcohol) or adhesive tape to make aluminum electrolytic capacitor
1. Winding process and technical requirements:
1.1, anode foil and cathode foil overlap is good, if the anode foil and cathode foil overlap is not good, will cause the following phenomenon
a, The "effective" area (overlapping part) of the metal plate of the capacitor decreases, resulting in the decrease of the capacitance.
B, after winding, the element core pulling, as shown in the following figure
c, The prime is spiral, as shown below
1.2. The center point of the well wound prime and the two leads shall be in line without eccentricity, as shown in the figure
Bad winding condition, 4 legend
1.3. The distance between the two leads of the prime element and the distance between the holes of the sealing rubber plug shall be matched, otherwise, poor sealing will be caused, and leakage will be caused in serious cases, as well as the scratch (open circuit, semi open circuit) on the contact between the aluminum tongue and the aluminum foil, which will greatly shorten the service life of the capacitor.
The winding mandrel shall be selected according to the outer diameter of the product, as shown in the table below. For the data in the table, the winding pins of different mandrel shall be selected. After winding, the element can be put into the aluminum shell smoothly, and a certain gap shall be reserved with the aluminum shell
Shell diameter / mm, ultra small, 5, 6, 8, 10, 13, 16, 18, 22
Mandrel diameter / mm 0.8 ~ 1.01.2 ~ 1.51.5 ~ 1.8 1.82.0 ~ 2.53 3.5 ~ 4 3.5 ~ 4 3.5 ~ 4
精品人妻少妇视频,黄黄色视频免费在线观看,√天堂资源网最新版在线,看日韩免费高清一区二区三区,黑人一级二级三级毛片,色图在线视频国产,欧美精品久久久久久久免费,久久影院国产精品,欧美一级特黄特色大片免费观看
,亚洲精品在线观看视频在线观看,宝宝边吃奶边放屁怎么回事
